T & L Mount
Attach a T&L mount to the side of your pier with two simple hand knobs, and you’re ready for an “L” section. Attach one on the left and one on the right for a “T.” Attach two side-by-side and you’re ready for a double-wide “L” platform. T&L mounts are made for 2.5 ft wide, 4 ft wide and 6 ft wide sections.
T & L Mount
Five feet long, our bench comes in vinyl Deck or Cedar, so it’s going to match your pier. The bench also comes with or without cup holders. It attaches to the outside of the pier with our hand tightening grippers, leaving you plenty of deck space. The center support-gusset hooks under the main aluminum frame through the slats of the decking for a secure feeling. Best of all, you can face it toward the lake. How ’bout that?
Stairsteps adjust to different depths as easily as our sections do, with two cam mechanisms. But there’s a bonus, you can vary the angle too. Make the steps vertical if you want, or almost horizontal. Two simple hand knobs secure the Stairsteps firmly to the dock.
The corner cutter attaches from above with, you guessed it, our grippers. The guys around the shop refer to the diagonal as the hypotenuse.
Our GRIPPER BUMPERS include hardware that attaches anywhere along the side of your pier.
Our Leg Bumpers attach to the legs. That’s why we call them Leg Bumpers. They can be oriented toward the front, toward the side, or halfway in between.
These state-of-the-art bumpers attach to the leg sleeves. In addition to their 30″ length, they are height-adjustable through a vertical range of an additional 22″. They can be oriented to the side, to the front or anywhere in between. Most important, they are dual layered, so they won’t bottom out.
Gripper Bumpers attach to the side rail of the pier anywhere along its length with a simple hand knob. Length is 30.”
Bumpers come in fancy colors: white, black, gray, tan, blue, and green.
Deep Water Bracing
For water depths over about 4 – 4.5 ft we recommend our criss-cross bracing. It’s one of our cleverest accessories; you can add it after the fact, AND you won’t have to go diving to attach the bottom clamp. Our unique clamp tightens automatically AFTER you lower it to its bottom position. To see how that’s accomplished, just press one of the little buttons below.
Deep Water Bracing
Wrap the clamp around the leg at about the waterline.
the 2″ bolt partway through one of the holes.
Attach one end of the deep water brace to the bolt.
Close the clamp and run the bolt through.
Add the spring.
Lightly attach the wing nut.
Pivot the deep brace arm as far up as it will go
Tighten the wing nut as tightly as possible.
The clamp will remain loose so you can lower the arm.
Lower the clamp/arm as per the instructions.
Then bring the top of the arm over to the other leg.
As the arm pivots over, the clamp will tighten up and hold fast.
These unique cleats fold down when not in use. It’s hard to imagine a dock where that’s not a handy feature. Your toes will thank you.
Put them anywhere!
Available With Snap Clip
If you need to lock your panels to the frame, you want it to be easy and fast. Pier of d’Nort rejected dozens of schemes that weren’t easy or weren’t fast. This is the scheme that was both. One neat feature of these panel clips is that they won’t get in each other’s way when it comes to stacking your panels over the winter. The locks are staggered deliberately, for that reason.
Independent (Bluff Mount) Legs
You’re now able to back your dock up against a bluff where it might be too steep or unaccommodating for other mounting methods. This leg can be quickly mounted anywhere along the pier. Footpads can be oriented parallel to shore if need be. You can even bolt these legs to the side of your homemade dock and have all the advantages of a quick and secure height adjustment capability. We’d rather that you bought our pier though.
Bluff Mount Legs
Screw the Auger Post into the ground to anchor your dock down. Great for docks holding larger boats on bigger waters. Also great for rivers. You can even put bumpers on them. Don’t buy them if your bottom is bedrock, they take way too long to screw in.
Screw this beefy bad boy into the ground and you can tie the bow of your boat to something that’s not going to lean over. The specially designed sliding vanes dig into the substrate and provide a broad-area resistance to lateral movement. It’s an easy alternative to a boat lift.
Mooring Pole comes with or without an attachment rope and clips.
Just screw the Mooring Pole in. The stabilizing vane assembly allows that.
Once the pole is screwed in and the vanes are tamped down a bit, the pole is ready for use.
Got a really hard bottom and deep water? This item is nice for firmer substrates if you don’t want to get into the water for your first installation. It’s particularly nice if you’re installing into over-your-head water.
The Extraction Mast will allow one person to lower a section into the water temporarily to “test the waters” as it were
If the legs need adjustment, simply bring the section back up and adjust the legs from your high and dry perch on the dock. Note how the dock section just stays there all by itself. And the mast is designed to snuggle up in its little space, ready to lower that
section back in.
Remember, this device is for firm-bottomed lakes like rocks, gravel, sand and some silt.
Panel Carrying Handle
Since the spacing between boards is sometimes less than the thickness of some fingers, we thought we’d make this device.
For the do-it-yourself er we sell our gripper mounts all by themselves. Bolt or weld whatever you like to the gripper for easy attach/remove capability. It’s aluminum so it’s easy to work with.
Tip-A-Canoe and Kayak Too
Easily scoops your canoe or kayak out of the water and rotates it up to waist height so you can store it securely upside down. Available nowhere else.
Tip-A-Canoe and Kayak Too
How many decades have you been waiting for this?
What could be easier?
Occasionally ordinances or safety issues require the installation of handrails, so we offer them.
DISPLAY OUR GREAT AMERICAN FLAG WITH PRIDE
Extends up to 20 ft tall! Comes with solid mounting hardware. Display it anywhere on the pier where there is structural material.
Attach for additional safety as you move between your pier and a boat. 18” Only (3 board)
Create a space to keep ‘off pier’ or as a step between your boat and pier. Available in two sizes to meet whatever your need!
Paddle board Rack
Made for one!
Shatterproof Stemware and Stemware Holder
Fits snuggly inside a bench or boat cup holder!